THE INDUSTRIAL FLOOR EXPERT             telephone    +36 1 212 7265          mail    Send email           place    63/c Szabó Ilonka Street , Budapest H-1015

facebook     youtube     google plus

logo 122x70



General properties

ARMATOP is pre-blended cementitious fireproof powder mixture, containing selected mineral hard aggregates, special cements and compatible admixtures. Added corundum powder extremely increases abrasion resistance of the floor. ARMATOP is used to create very durable topping of monolithic concrete floors. Immediately after usual fitting of the concrete slab ARMATOP is sprinkled on the fresh wet concrete. Repeated power trowelling forms durable, smooth and non–slip surface. ARMATOP topping provides increased resistance to the penetration of oil and grease. Industrial floors with ARMATOP dry shake topping are extensively used in warehouses, factories, workshops, shopping centres etc. and generally everywhere, where durable and abrasion resistant surface is required.


Light gray
Antracit black
Tile red


Special properties

resistance to higher duty dust free cost effective fast track guaranteed quality - no site production Maintenance free

Method of use

ARMATOP should be spread and screeded evenly onto the freshly laid concrete slab in one or two stages, the total amount of the material being 5 kg/m2. For an area of lighter loads reduction of the ARMATOP amount to 3 kg/m2 is possible. After removing or evaporating bleed water from the fresh wet and fully compacted concrete the first adequate part of the powder (2.5 kg/m2, or 1.5 kg/m2) should be shake-applied evenly onto the screeded slab. The first stage should be worked into the substrate followed immediately with shaking of the second portion (2.5 kg/m2). To achieve final mechanical properties of the topping using powered trowel machines is essential. Repeated powerfloating should follow the gradual hardening of concrete. Finished floor should be cured and sealed with FLOORSEAL & AQUASEAL in the typical amount of 0.10 l/m2. This clear solution gives the surface additional hardening, prevents dusting and rapidly reduces liquid absorption. In accordance with the specification of slab design, joints should be created in 24 hours after completion of the floor. All joints always reach through the entire topping layer. As a common phenomenon of repeated power trowelling, which brings tension into the surface, some very fine cracks may appear on the floor surface. This observable fact is typical for all power trowelled concrete surfaces and bears no influence on beneficial properties of the floor.

Technical data

ABRASION RESISTANCE up to 1,53 cm3 / 50 cm2 - Böhme (DIN 52 108)
COMPRESSIVE STRENGTH min. 70 MPa after 28 days according to ON 701
PACKAGING ARMATOP is supplied in 25 kg bags with PE internal insert. COVERAGE / YIELD ARMATOP 5 m2 / 25 kg (5 kg / m2) FLOORSEAL & AQUASEAL 200 m2 / 20 l
COLOURS ARMATOP is supplied in natural grey colour (colour of concrete) and in green, ocker, tile red, plum, light grey and black. Possible other colours to be consulted.
SHELF LIFE 12 months from the dispatching date in original unopened packs. Protect from frost and wet conditions.

Safety and health protection

The product contains cement; therefore it is necessary to wear protective gloves and goggles. Further data are mentioned in a separate document concerning the protection of health at the work with the product and on its cover.
Maintenance and cleaning

The instructions for the routine cleaning, repair of possible small damages and additional colour treatment of the surface are at disposal.


Dry shake floors 

 Name Armadur  Armatop Armadur S Terradur 
 Abraision class A6  A3  A6  A3
 With Chemcure S curing  *  A1,5  *  *
 Stress degree  Middle  Big Middle Middle
 Oil resistance  yes yes yes yes
 Consumption: kg/m2  4-6  4-6  4-6  7-912-15**

* not tested
** grout
According to MSZ EN 13892